Power Press Machine for Saudi Arabia (KSA)
National Cutting Tools builds mechanical C-frame and H-frame power presses from roughly 20 to 150 tonnes for blanking, piercing and cup forming at its works in Ludhiana, Punjab, and ships them to Riyadh, Jeddah, Dammam, Al Khobar, Jubail and Yanbu through King Abdulaziz Port, Dammam. The machines produce scaffold cups, base plates, brackets, gussets and cleats, and are built to the geometry and tolerances called up by EN 692 for mechanical press safety and IS 5062 for the frame. Every consignment for Saudi Arabia is rewound for 60 Hz, which is a different motor and gearbox selection rather than a nameplate change: at 60 Hz an unmodified 50 Hz motor runs 20 percent fast, shifting cycle timing, hydraulic flow and weld travel speed.
Where the demand comes from
Cup, plate and bracket pressing for Saudi scaffold manufacture is scaling alongside the welding capacity, and IKTVA scoring applies to pressed components too. Presses for the Kingdom are supplied with 60 Hz drive trains and guarding set for local inspection.
Delivered to: Riyadh, Jeddah, Dammam, Al Khobar, Jubail, Yanbu, Mecca, Medina
Power Press Machine available for Saudi Arabia (KSA)
C Frame Power Press
- Type: Power Press Machine
- Press Ram Material: Alloy Steel
- Press Capacity: 10 Ton – 200 Ton
Pillar Type Power Press
- Voltage: 440V
- Automatic Grade: Automatic
- Power Source: Hydraulic
Friction Screw Press
- Feature: Specification
- Press Capacity: 100 – 1000 Tons (model dependent)
- Type: Friction Drive / Screw Type
Electrical build
Supply: 380V, 3-phase, 60 Hz. Rewound for 60 Hz, which is a different motor and gearbox selection rather than a nameplate change: at 60 Hz an unmodified 50 Hz motor runs 20 percent fast, shifting cycle timing, hydraulic flow and weld travel speed.
Shipping & crating
Press frames are dense: a 100 tonne C-frame is typically over-dimension for a standard container and moves as flat rack or break-bulk, which changes the freight quotation materially. Sailings from Mundra and Nhava Sheva reach Dammam in 6 to 9 days, or Jeddah Islamic Port on the Red Sea rotation, discharging at King Abdulaziz Port, Dammam (SADMM). Machines are crated to ISPM-15 heat-treated standard with desiccant and a vapour barrier, and the packing list, commercial invoice and chamber-attested Certificate of Origin travel with the consignment.
Standards & import documentation
Machines in this class normally clear customs under HS heading 8462.49. The press is run off on the buyer's own die to prove shut height, and the guarding and two-hand control are set to the importing country's inspection requirement. Import clearance in Saudi Arabia runs on SASO technical regulations declared through the SABER platform, with a Product Certificate of Conformity issued per consignment. The works issues the manufacturer test certificate, electrical schematic and material test report with every machine, so the buyer's submittal pack is complete on arrival rather than assembled afterwards.
| Conformity | SASO technical regulations declared through the SABER platform; Product Certificate of Conformity prepared per shipment. Pre-shipment inspection accepted at the Ludhiana works. |
| Tariff headings | Typical headings: 8515.31 (arc/MIG welding machines), 8459.70 (threading and tapping machines), 8462.49 (punching and notching machines), 8479.89 (special purpose machines). |
| Port (UN/LOCODE) | King Abdulaziz Port, Dammam (SADMM) |
| Incoterms offered | EXW Ludhiana, FOB Mundra / Nhava Sheva, CIF Dammam or CIF Jeddah |
Spares & after-sales support
Wear parts for this class are clutch and brake linings, flywheel bearings, slide gibs and the overload protection discs. Interior sites at Riyadh and NEOM combine 50 C summer peaks with abrasive dust; coastal Jubail and Jeddah add chloride-laden humidity. Machines are specified accordingly, and the 60 Hz requirement is engineered in at the motor and pump stage. Spare-part orders are quoted against the machine serial number.