Rebar Machine for Malaysia
National Cutting Tools builds rebar thread rolling, upsetting and cold forging equipment that prepares bar ends for mechanical splice couplers instead of lapping at its works in Ludhiana, Punjab, and ships them to Kuala Lumpur, Klang, Shah Alam, Johor Bahru, Pasir Gudang and Penang through Port Klang. The machines produce parallel-thread and taper-thread bar ends from 12 mm to 40 mm, and are built to the geometry and tolerances called up by BS 4449, ASTM A615 and A706 for the bar, and ISO 15835 for the coupler system. Every consignment for Malaysia is supplied with tropicalised motor insulation rated for high ambient humidity, which attacks electrical windings long before it affects the mechanics.
Where the demand comes from
MRT and Penang LRT civils specify mechanical splices in deep pile caps and diaphragm walls, and Malaysian rebar fabricators buy threading capacity to serve them. AIFTA can remove duty on the 8459.70 heading where the consignment qualifies.
Delivered to: Kuala Lumpur, Klang, Shah Alam, Johor Bahru, Pasir Gudang, Penang, Ipoh, Kuching
Rebar Machine available for Malaysia
Rebar Thread Cutting Machine
- Machine Type: Thread Cutting
- Material: Cast Iron, Stainless Steel
- Motor Power: 1.5 KW To 5.5 KW
Rebar Cold Forging Machine
- Rated Extrusion Force: 550 KN
- Use: Lifespan 30 Years
- Voltage: 380V
Rebar Coupler
- Model Number: 16 MM TO 40 MM
- Brand Name: NCT
- Material: FOR 500 AND 600 – TATA, SAIL & Other Rebars
Electrical build
Supply: 415V, 3-phase, 50 Hz. Supplied with tropicalised motor insulation rated for high ambient humidity, which attacks electrical windings long before it affects the mechanics.
Shipping & crating
Threading and upsetting machines are compact enough for LCL, but the hydraulic power pack and cooling tank are usually crated separately to keep the gross weight per package inside the buyer's forklift rating. Port Klang and Penang Port are served from Nhava Sheva and Mundra in 8 to 12 days, discharging at Port Klang (MYPKG). Machines are crated to ISPM-15 heat-treated standard with desiccant and a vapour barrier, and the packing list, commercial invoice and chamber-attested Certificate of Origin travel with the consignment.
Standards & import documentation
Machines in this class normally clear customs under HS heading 8459.70. Coupler pull-out testing against the specified bar grade is the acceptance criterion, so a sample thread set is rolled and tested before dispatch. Import clearance in Malaysia runs on SIRIM QAS inspection where the buyer specifies it, Energy Commission (Suruhanjaya Tenaga) electrical requirements, and AIFTA Form AI where the consignment qualifies for preferential duty. The works issues the manufacturer test certificate, electrical schematic and material test report with every machine, so the buyer's submittal pack is complete on arrival rather than assembled afterwards.
| Conformity | SIRIM QAS inspection where the buyer specifies it, and Energy Commission (Suruhanjaya Tenaga) electrical requirements; AIFTA Form AI issued where the consignment qualifies for preferential duty. |
| Tariff headings | Typical headings: 8515.31 (arc/MIG welding machines), 8459.70 (threading and tapping machines), 8462.29 (bending and forming presses), 8479.89 (special purpose machines). |
| Port (UN/LOCODE) | Port Klang (MYPKG) |
| Incoterms offered | EXW Ludhiana, FOB Mundra / Nhava Sheva, CIF Port Klang or CIF Penang |
Spares & after-sales support
Wear parts for this class are thread rolling dies, chaser sets, hydraulic seals and the bar clamping jaws. The monsoon and constant humidity are the design constraint here, not heat. Tropicalised motor insulation is specified for the Malaysia rotation, and the ASEAN-India FTA can remove duty on qualifying headings. Spare-part orders are quoted against the machine serial number.